SAE J2271_200905

SAE J2271_200905

Click here to purchase

This SAE Parts Standard provides dimensional and quality assurance requirements for studs in the following configurations in standard materials used for ship system applications:

  1. Continuous thread studs in UNRC and 8UNR series in the following threads and diameters:

    • UNRC threads (1/4 through 4 inches)

    • UNRF threads (1/4 through 1-1/2 inches)

    • 8UNR threads (1-1/8 through 4 inches)

  2. Double end studs (clamping type) where both ends are of the same minimum thread length in the following threads and diameters:

    • UNRC threads (1/4 through 4 inches)

    • UNRF threads (1/4 through 1-1/2 inches)

    • 8UNR threads (1-1/8 through 4 inches)

  3. Different thread forms on each end are permissible.

  4. Double end studs (tap end type) where the tap end thread length is equivalent to 1-1/2 nominal diameters:

Product Details

Published:
05/01/2009
File Size:
1 file , 410 KB
SAE J2271_200905

SAE J2271_200905

Click here to purchase
This SAE Parts Standard provides dimensional and quality assurance requirements for studs in the following configurations in standard materials used for ship system applications: a. Continuous thread studs in UNRC and 8UNR series in the following threads and diameters: UNRC threads (0.190 through 4 inches); UNRF threads (0.190 through 1-1/2 inches); 8UNR threads (1-1/8 through 4 inches)

b. Double end studs (clamping type) where both ends are of the same minimum thread length in the following threads and diameters: UNRC threads (1/4 through 4 inches); UNRF threads (1/4 through 1-1/2 inches); 8UNR threads (1-1/8 through 4 inches); Different thread forms on each end are permissible.

c. Double end studs (tap end type) where the tap end thread length is equivalent to 1-1/2 nominal diameters: Tap End Thread Forms and Diameters Nut End Thread Forms and Diameters; NC-5 interference-fit tap end threads (1/4 through 1-1/2 inches); UNRC threads (1/4 through 4 inches) • UNRC threads (1/4 through 4 inches); UNRF threads (1/4 through 1-1/2 inches); UNRF threads (1/4 through 1-1/2 inches); 8UNR threads (1-1/8 through 4 inches); 8UNR threads (1-1/8 through 4 Inches)

These studs are primarily for use in ship systems and equipment. The continuous thread studs and the reduced body diameter double end studs are configurations particularly suited to applications that are subject to high impact (H.I.) shock requirements.

Product Details

Published:
05/04/2009
File Size:
1 file , 410 KB

You may also like

SAE J2862_202305

SAE J2862_202305

User’s Manual for the Small Adult Female Hybrid III Test Dummy (Stabilized: May 2023)standard by SAE International, 05/22/2023

SAE AS22520/48A

SAE AS22520/48A

CRIMP TOOLS, TYPE 1, HAND OR POWER ACTUATED, WIRE TERMINATION, HYDRAULIC TOOL FOR WIRE BARREL SIZES 0000 THROUGH 8standard by...

SAE AS4832B

SAE AS4832B

Gland Design: Nominal 3/8 Inch Cross Section for Compression-Type Sealsstandard by SAE International, 06/12/2023

SAE AS7477J

SAE AS7477J

Bolts and Screws, Steel, UNS S66286 Tensile Strength 130 ksi, Procurement Specificationstandard by SAE International, 08/01/2023

Back to Top